Make drying recovery recorder. Explore recovery logging and consistent measurement.
Public beta missionThese revised instructions are open for learning while actual-kit testing is pending. A grown-up must confirm every setup check before power is connected. If a rating, pin card or required check is missing, explore the idea on screen and leave the physical build unpowered.
5 · Inventor Arcade
Your new skill: Recovery logging and consistent measurement
Arduino UnoUSB A-to-B data cableHalf-size breadboardMale–male / male–female jumper wires (as needed for actual module terminals)Water sensor, 1 button
Gather from home
Computer with Arduino IDE and Serial MonitorShallow trayTissueClean waterHousehold spoon or dropperPaper towel
Reuse the parts between missions; these are not 45 simultaneous installations. Red/yellow/green means those three monochrome colours. RGB is a separate component with three channels.
BEFORE YOU BUILD
Unplug USB before changing connections. Use only the USB supply for this build; never connect 9V to 5V or a signal pin, and never connect to mains. An adult verifies variant, printed pin labels and resistor values before powering. Stop and unplug if a part becomes hot or damaged. Adult handles damp tissue. Keep Uno/computer and connectors dry and outside tray; wet only exposed tracks briefly. Do not run unattended.
YOUR REWARD
+30 XPMission completion
PREDICT BEFORE YOU BEGIN
Before the test: which input will change, and what signal or reading do you expect?
BEFORE YOU BUILD
Parent check: exact part variant, labelled pins and stated values. If a check cannot be confirmed, keep this physical build unpowered and explore the code and prediction instead.
YOUR CHALLENGE
Build drying recovery recorder and prove its rule.
NEW POWER-UP
Recovery logging and consistent measurement
You have explored duration states and acknowledgement. Now try recovery logging and consistent measurement.
Adult help: Adult helps with computer setup, first wiring and any water/cutting. Learner predicts, tests and explains.
See the idea before you build
How a breadboard connects inside
Each coloured strip is one connected group. Different numbered rows stay separate. This explains the board; use the mission’s exact connection reference for component positions. Check rail breaks on your supplied board.
See the idea, then follow this mission’s exact pin-to-pin map below. · Tap to enlargeOpen full-size referencePin-to-pin reference for this sketch. Match printed labels and actual component variant. · Tap to enlargeOpen full-size reference
Open the complete Arduino code
Copy the complete code into Arduino IDE or download the sketch. Follow the matching component card before connecting power.
// First Wonder Brain Bots 38 — Drying Recovery Recorder
// USB-powered model. Unplug before rewiring. Serial Monitor: 9600 baud.
unsigned long started=0;
unsigned long lastReport=0;
int state=0;
const byte buttonPins[]={2};const byte buttonCount=1;
bool rawButton[4]={HIGH,HIGH,HIGH,HIGH},stableButton[4]={HIGH,HIGH,HIGH,HIGH},pressedEvent[4]={false,false,false,false};
unsigned long changedAt[4]={0,0,0,0};
void scanButtons(unsigned long now){for(byte i=0;i<buttonCount;i++){
pressedEvent[i]=false;bool raw=digitalRead(buttonPins[i]);
if(raw!=rawButton[i]){rawButton[i]=raw;changedAt[i]=now;}
if(now-changedAt[i]>=30&&raw!=stableButton[i]){stableButton[i]=raw;pressedEvent[i]=raw==LOW;}
}}
bool press(byte index){return pressedEvent[index];}
void setup(){Serial.begin(9600);pinMode(2,INPUT_PULLUP);Serial.println("Ready. Follow your mission test.");}
void loop(){
unsigned long now=millis();
scanButtons(now);
if(press(0)){started=now;state=!state;Serial.println(state?"LOG START":"LOG STOP");}
if(state&&now-lastReport>=1000){lastReport=now;Serial.print(now-started);Serial.print(",");Serial.println(analogRead(A1));}
}
Check the connection map
CONNECTION MAP
Build the electrical path before you test.
Keep power disconnected while changing connections.
JoinConnectWhy it matters
PowerSupplied USB data cable → Uno USB socket; computer at other endThe same cable uploads and supplies this model. Unplug before wiring.
Shared referenceUno GND → breadboard ground railAll module GND terminals use this same reference. Check whether your rail is split.
Button 1D2 → one switched terminal; opposite switched terminal → GNDINPUT_PULLUP: press reads LOW. Four-leg buttons have internally joined pairs; use a verified switched pair.
Water boardVerified + → 5V; − → GND; S/analog signal → A1Keep supply and connectors outside the tray; only tracks touch damp tissue.
Kit variant and values confirmed by an adult
All pins match the map; USB was disconnected while wiring
Test includes expected, non-triggering and recovery cases
BUILD PATH
STEP 1 OF 6
Meet your mission
Try · Notice · ExplainRead the checkpoint, make a prediction, then test your idea.
You will explore recovery logging and consistent measurement. Gather the kit and home materials below. Unplug USB. Match the part names and printed labels.
Watch this step
A video demonstration will appear here when it is ready. You can follow the written step now.
Read the video instructions
You will explore recovery logging and consistent measurement. Gather the kit and home materials below. Unplug USB. Match the part names and printed labels.
Need a diagram for this step?
See the idea, then follow this mission’s exact pin-to-pin map below. · Tap to enlargeOpen full-size referencePin-to-pin reference for this sketch. Match printed labels and actual component variant. · Tap to enlargeOpen full-size reference
WHAT'S REALLY HAPPENING?
Why it works
Recovery logging and consistent measurement. Water tracks respond to conductivity and contact, not universal depth or plant health. Check your rule against an example where it should respond and one where it should not. Contact differences would change readings as well as drying.
This is a tabletop learning model. Real systems also need reliable power, robust sensors and careful handling of unknown measurements; this kit model is not a safety or security device.
FAIR-TEST CHALLENGE
Change one input or setting at a time; keep the wiring and protection unchanged. Repeat three trials.
WHEN IT DOESN'T WORK YET
Debug one clue at a time.
Upload or port missing
Likely cause: Wrong board, port or cable connection
Try this first: Check Arduino Uno selection and supplied data cable. Unplug external wiring before checking upload on built-in LED.
Signal does not match the test
Likely cause: Pin labels, input calibration or variant differs
Try this first: Unplug. Compare every connection with the map. Return to the earlier single-input mission; test one subsystem at a time.
Reading is unknown or unstable
Likely cause: Sensor settling, target, contact or calibration
Try this first: Follow the exact test setup; allow settling, use a flat target or check module pinout unpowered. Never replace unknown with a guessed safe reading.
CLEAN, RESET AND STORE
Disconnect USB, remove wires carefully and store components dry.